Il s'agit du premier module basé sur une vactrol dans le système A-100. Une vactrol est une combinaison d'une résistance dépendante de la lumière (LDR) et d'une LED (diode électroluminescente), toutes deux placées dans un petit boîtier résistant à la lumière. Pour plus de détails sur les vactrols, veuillez consulter les informations de la page Vactrol Basics. L'augmentation de la luminosité de la LED entraîne une diminution de la résistance de la LDR (par exemple, le module de tension contrôlé par la lumière A-179 est une application d'une LDR). Cet effet peut être utilisé dans des circuits qui nécessitent des résistances variables pour obtenir la fonction désirée (par exemple, VCF, VCA, VC phasers, VC trigger delays, VC slew limiters, VC Envelope Generators, VC LFOs, VCOs et bien d'autres). L'avantage des vactrols par rapport à d'autres solutions (par exemple les OTA, les diodes, les transistors ou les FET en tant que résistances variables) est qu'ils se comportent comme une résistance Ohm normale et peuvent supporter des tensions élevées sans provoquer de distorsion. C'est probablement la raison pour laquelle le son des circuits à base de vactrol est généralement décrit comme doux ou moelleux. Les inconvénients sont le coût et par conséquent les dépenses et la cohérence pas exactement définie entre le courant de la LED et la résistance de la LDR. Pour chaque vactrol, la résistance du LDR diminue lorsque le courant de la LED augmente, mais les tolérances mécaniques et électriques font que chaque vactrol se comporte un peu différemment (par exemple, en raison des différences d'alignement et de distance entre la LED et le LDR, de la luminosité différente des LED pour le même courant).
Le module A-101-1 est un filtre multitype spécial basé sur une idée de Nyle A. Steiner (publiée dans Electronic Design, numéro 25, décembre 1974, page 96 et suivantes). Le circuit utilise la conception standard d'un filtre d'amplificateur non inverseur. Différents types de filtres (passe-bas / LP, passe-bande / BP, passe-haut / HP) sont réalisés en injectant le signal audio en différents points du circuit et en utilisant une sortie commune pour tous les types de filtres. Il est possible d'injecter simultanément trois signaux audio différents dans le filtre. Chaque signal est filtré en conséquence (LP resp. BP resp. HP) et la somme des trois signaux filtrés apparaît à la sortie. Bien entendu, il est possible d'alimenter les trois entrées avec le même signal. Dans ce cas, on obtient différentes combinaisons de LP/BP/HP en fonction des réglages des trois atténuateurs d'entrée pour LP/BP/HP. Il est même possible d'utiliser un filtre Notch (non disponible dans le modèle original). Les entrées du filtre sont normalisées, c'est-à-dire que l'entrée BP est connectée à la prise jack LP à condition qu'aucun câble ne soit branché sur la prise BP (il en va de même pour les entrées HP/BP). Si vous êtes intéressé par les détails techniques concernant le A-101-1, nous disposons d'informations complémentaires : A-101-1 Technical Details.
Contrairement au circuit original, des vactrols sont utilisés à la place des diodes comme résistances variables pour le contrôle de la fréquence du filtre. En raison de la réponse "tordue" des vactrols, le filtre n'a pas de norme de contrôle de fréquence exacte (comme V/Oct). Les tolérances inévitables entre les différents vactrols conduiront à un son individuel de chaque module et à un comportement de résonance individuel. Même le contrôle de la résonance est réalisé avec des vactrols. Par conséquent, ce paramètre est également contrôlé par la tension. La résonance peut être augmentée jusqu'à l'auto-oscillation. La résonance et, par conséquent, l'auto-oscillation peuvent varier en fonction de la fréquence du filtre en raison des tolérances des vactrols.
Les deux sorties audio constituent une caractéristique particulière du module. La sortie 1 est la sortie du circuit original. Dans le circuit original de Nyle A. Steiner, le niveau de sortie dépendait nettement de la résonance (résonance plus élevée = niveau de sortie plus élevé). La sortie 2 compense ce comportement par l'utilisation d'une commande supplémentaire qui est connectée en série à la commande qui contrôle la résonance. Cette commande supplémentaire forme un atténuateur (ou un simple VCA) qui compense approximativement l'augmentation du niveau pour des réglages de résonance plus élevés.
Deux afficheurs LED indiquent la fréquence actuelle et le réglage de la résonance. Les LED sont connectées en série aux LED à l'intérieur des vactrols et affichent en conséquence l'illumination des LED à l'intérieur des vactrols.
Breite/Width : 16TE / 16HP / 80.9 mm
Tiefe/Depth : 50 mm (gemessen ab der Rückseite der Frontplatte / measured from the rear side of the front panel)
Strombedarf/Current : 30 mA