Godlyke Gd-Pg1M Power Grip 1 Meter

GodlykeSKU: 1003910

Price:
Sale price$18.25Found a better price?

Special Order This item is not in stock and can be obtained by placing a Special Order. Please note that Special Orders cannot be canceled or refunded.
Estimated ship date if ordered now:
Contact Our Specialists Need specific product information or not sure where to start? Our in-house specialists are here to help you make the right decision. With extensive knowledge of our products, they are ready and eager to assist you.

Description

Pedal Board Tape - Pedalboard Dual Lock and Velcro Alternative

For the best Pedalboard Dual Lock and Velcro Alternative, try Power-All Power-Grip. Simple, yet ingenious, Power-Grip pedal board tape mates to itself via rows of tiny mushroom-shaped posts that form a much stronger bond than traditional "hook & loop" Velcro fasteners. Just cut to size, apply, and GRIP!

 

Power-Grip Is Available In The Following Configurations

  • 1-Meter Roll (add to cart above) – Single-sided, 1-meter (39.37 inch) long x 1 inch wide roll - approximately enough for 6 standard-sized pedals. $14.95
  • 5-Meter Roll – Single-sided, 5-meter (Approx. 16 feet) x 1inch wide roll – Enough tape to cover PT-JR & still have some tape left over for your pedal backs.  $69 (10% off single roll price)
  • 10-Meter Roll – Single-sided, 10-meter (Approx. 33 feet) x 1 inch wide roll – Enough tape to cover PT-3 & still have some tape left over for your pedal backs.  $129 (15% off single roll price)
  • Single Pedal Pack - Two x 4 inch long x 1 inch wide strips. Enough tape for one standard sized pedal. $3.49

POWER-GRIP is the best Solution for securing your guitar pedals to your pedalboard (No Hype).

 

INSTRUCTIONS FOR USE

  • Mounting surfaces must be free of grease, dirt, loose particles, and moisture.
  • Mounting surfaces must be smooth, even and stable.
  • Metal surfaces should be cleaned with Acetone prior to mounting.
  • Plastic & lacquered surfaces should be cleaned with Lighter Fluid prior to mounting.
  • External temperature should be approximately 68° F (20°C) while applying Power-Grip.
  • Cut two identically-sized strips of Power-Grip to the desired length.
  • Fasten one strip to the object to be mounted and the other strip to the mounting surface.
  • Press tape down firmly and evenly – use of a pressure roller is recommended.
  • Use additional pairs of strips as needed for a stronger grip.
  • For maximum adhesion, expose the adhesive to hot air (140°-180° F) for at least 2 minutes after mounting.
  • Allow at least 24 hours for the Power-Grip adhesive to set.
  • Press the two Power-Grip strips together and GRIP!

NOTES REGARDING USE

  • The Power-Grip adhesive backing will form a permanent bond over time. Once this occurs, Power-Grip may damage painted surfaces or leave adhesive residue if removed. Residue can be removed with Acetone or Lighter Fluid.
  • Power-Grip adheres best to smooth surfaces such as coated metal or plastic. It will not adhere well to very rough surfaces such as unfinished wood, etc.
  • When in doubt, test adhesion to the surface FIRST using a small piece of Power-Grip.
  • We do not guarantee that Power-Grip will be suitable for all applications and we do not take responsibility for loss or damage to property due to improper use/mounting of Power-Grip.

 

Estimate shipping

Request an ETA on: Godlyke Gd-Pg1M Power Grip 1 Meter

ETA are subject to change. By clicking submit I understand the ETA might change once the order comes through.
Thank you for submitting your ETA Request! Our sales team will reach out with an ETA shortly.

You may also like

Recently viewed

Free Shipping

We offer Free Shipping on all orders over 199$. Conditions may apply.

Gift Card

Looking for a perfect last minute gift? Gift cards can be redeemed online or in store

Quick Financing

Shop now, pay later with Flexiti! Get approved in less than 60 seconds

100% secure

SSL (Secure Socket Layer) technology to encrypt data during the checkout process